An investigation of the PM2.5 concentrations and cumulative inhaled dose during subway commutes in Changchun, China.

Air quality in subway systems is crucial as it affects the health of passengers and staff. Although most tests of PM2.5 concentrations in subway stations have taken place in public areas, PM2.5 is less understood in workplaces. Few studies have estimated the cumulative inhaled dose of passengers based on real-time changes in PM2.5 concentrations as they commute. To clarify the above issues, this study first measured PM2.5 concentrations in four subway stations in Changchun, China, where measuring points included five workrooms. Then, passengers' exposure to PM2.5 during the whole subway commute (20-30 min) was measured and segmented inhalation was calculated. The results showed that PM2.5 concentration in public places ranged from 50 to 180 µg/m3, and was strongly correlated with outdoors. While the PM2.5 average concentration in workplaces was 60 µg/m3, and it was less affected by outdoor PM2.5 concentration. Passenger's cumulative inhalations in single commuting were about 42 µg and 100 µg when the outdoor PM2.5 concentrations were 20-30 µg/m3 and 120-180 µg/m3, respectively. The PM2.5 inhalation in carriages accounted for the largest proportion of the entire commuting, about 25-40%, because of the longer exposure time and higher PM2.5 concentrations. It is recommended to improve the tightness of the carriage and filter the fresh air to improve the air quality inside. The average daily PM2.5 inhaled by staff was 513.53 µg, which was 5-12 times higher than that of passengers. Installing air purification devices in workplaces and reminding staff to take personal protection can positively protect their health.

Using general practitioners with an extended role in spinal practice for the initial assessment of patients referred to spinal surgeons: preliminary experience and challenges.

AIM: To describe experience using general practitioners (GPs), with an extended role (GPwER) in spinal medicine, to expedite assessment, triage, and management of patients referred from primary care for specialist spinal surgical opinion. BACKGROUND: Low back and neck pain are common conditions in primary care. Indiscriminate or inappropriate referral to a spinal surgeon contributes to long waiting times. Previous attempts at triaging patients who really require a surgical opinion have used practice nurses, physiotherapists, clinical algorithms, and interdisciplinary screening clinics. METHODS: Within the setting of an independent spinal care centre, we have used GPs specially trained in spinal practice to expedite the assessment and triage of new referrals between 2015 and 2021. We reviewed feedback from a Patient Satisfaction Questionnaire and the postgraduate backgrounds, training, practice with regard to triage of new referrals, and experiences of the GPs who were recruited. FINDINGS: Six GPwER had a mean of 26 years of postgraduate experience before appointment (range 10-44 years). The first four GPwER, appointed between 2015 and 2018, underwent an ad hoc in-house, interdisciplinary training programme and saw 2994 new patients between 2016 and 2020. After GPwER, assessment in only 18.9% (range 12.6 to 22.7%) of these patients was a spinal surgical opinion deemed necessary. Waiting times to see the spinal surgeon remained at 6-8 weeks despite a three-fold annual increase (from 340 to 1058) in new referrals. A Patient Satisfaction Questionnaire revealed high levels of satisfaction with the performances of the GPwER across seven dimensions. A dedicated training programme was designed in 2020, and the last two appointees underwent 20 h of clinical teaching prior to practice. Initial experience using GPwER, here termed 'Spinal Clinicians', suggests they are efficient at screening for patients needing spinal surgical referral. Establishing a recognised training programme, assessment, and certification for these practitioners are the next challenges.

Degenerative Cervical Myelopathy: A 7-Letter Coding System That Supports Decision-Making for the Surgical Approach.

OBJECTIVE: To validate with a prospective study a decision-supporting coding system for the surgical approach for multilevel degenerative cervical myelopathy. METHODS: Ten cases were presented on an internet platform, including clinical and imaging data. A single-approach (G1), a choice between 2 (G2), or 3 approaches (G3) were options. Senior and junior spine surgeons analyzed 7 parameters: location and extension of the compression of the spinal cord, C-spine alignment and instability, general morbidity and bone diseases, and K-line and multilevel corpectomy. For each parameter, an anterior, posterior, or combined approach was suggested. The most frequent letter or the last letter (if C) of the resulting 7-letter code (7LC) suggested the surgical approach. Each surgeon performed 2 reads per case within 8 weeks. RESULTS: G1: Interrater reliability between junior surgeons improved from the first read (κ = 0.40) to the second (κ = 0.76, p < 0.001) but did not change between senior surgeons (κ = 0.85). The intrarater reliability was similar for junior (κ = 0.78) and senior (κ = 0.71) surgeons. G2: Junior/senior surgeons agreed completely (58%/62%), partially (24%/23%), or did not agree (18%/15%) with the 7LC choice. G3: junior/senior surgeons agreed completely (50%/50%) or partially (50%/50%) with the 7LC choice. CONCLUSION: The 7LC showed good overall reliability. Junior surgeons went through a learning curve and converged to senior surgeons in the second read. The 7LC helps less experienced surgeons to analyze, in a structured manner, the relevant clinical and imaging parameters influencing the choice of the surgical approach, rather than simply pointing out the only correct one.

EZH2 promotes neoplastic transformation through VAV interaction-dependent extranuclear mechanisms.

Recently, we reported that the histone methyltransferase, EZH2, controls leukocyte migration through interaction with the cytoskeleton remodeling effector, VAV, and direct methylation of the cytoskeletal regulatory protein, Talin. However, it is unclear whether this extranuclear, epigenetic-independent function of EZH2 has a profound impact on the initiation of cellular transformation and metastasis. Here, we show that EZH2 increases Talin1 methylation and cleavage, thereby enhancing adhesion turnover and promoting accelerated tumorigenesis. This transforming capacity is abolished by targeted disruption of EZH2 interaction with VAV. Furthermore, our studies demonstrate that EZH2 in the cytoplasm is closely associated with cancer stem cell properties, and that overexpression of EZH2, a mutant EZH2 lacking its nuclear localization signal (EZH2ΔNLS), or a methyl-mimicking Talin1 mutant substantially promotes JAK2-dependent STAT3 activation and cellular transformation. Taken together, our results suggest a critical role for the VAV interaction-dependent, extranuclear action of EZH2 in neoplastic transformation.

Enhancement of Chlorella vulgaris harvesting via the electro-coagulation-flotation (ECF) method.

This article explores the potential of using an electro-coagulation-flotation (ECF) harvester to allow flotation of microalgae cells for surface harvesting. A response surface methodology (RSM) model was used to optimize ECF harvesting by adjusting electrode plate material, electrode plate number, charge of the electrodes, electrolyte concentration, and pH value of the culture solution. The result revealed that three aluminum electrode plates (one anode and two cathodes), brine solution (8 g/L), and acidity (pH = 4) of culture solution (optimized ECF harvester) The highest flocculant concentration was measured at 2966 mg/L after 60 min and showed a 79.8 % increase of flocculation concentration. Such results can provide a basis for designing a large-scale microalgae harvester for commercial use in the future.

Detecting Facet Joint and Lateral Mass Injuries of the Subaxial Cervical Spine in Major Trauma Patients.

STUDY DESIGN: Radiologic imaging measurement study. PURPOSE: To assess the accuracy of detecting lateral mass and facet joint injuries of the subaxial cervical spine on plain radiographs using computed tomography (CT) scan images as a reference standard; and the integrity of morphological landmarks of the lateral mass and facet joints of the subaxial cervical spine. OVERVIEW OF LITERATURE: Injuries of lateral mass and facet joints potentially lead to an unstable subaxial cervical spine and concomitant neurological sequelae. However, no study has evaluated the accuracy of detecting specific facet joint injuries. METHODS: Eight spinal surgeons scored four sets of the same, randomly re-ordered, 30 cases with and without facet joint injuries of the subaxial cervical spine. Two surveys included conventional plain radiographs series (test) and another two surveys included CT scan images (reference). Facet joint injury characteristics were assessed for accuracy and reliability. Raw agreement, Fleiss kappa, Cohen's kappa and intraclass correlation coefficient statistics were used for reliability analysis. Majority rules were used for accuracy analysis. RESULTS: Of the 21 facet joint injuries discerned on CT scan images, 10 were detected in both plain radiograph surveys (sensitivity, 0.48; 95% confidence interval [CI], 0.26-0.70). There were no false positive facet joint injuries in either of the first two X-ray surveys (specificity, 1.0; 95% CI, 0.63-1.0). Five of the 11 cases with missed injuries had an injury below the lowest visible articulating level on radiographs. CT scan images resulted in superior inter- and intra-rater agreement values for assessing morphologic injury characteristics of facet joint injuries. CONCLUSIONS: Plain radiographs are not accurate, nor reliable for the assessment of facet joint injuries of the subaxial cervical spine. CT scans offer reliable diagnostic information required for the detection and treatment planning of facet joint injuries.

Stress and eating behaviors.

Obesity is a heterogeneous construct that, despite multiple and diverse attempts, has been difficult to treat. One conceptualization gaining media and research attention in recent years is that foods, particularly hyperpalatable (e.g., high-fat, high sugar) ones, may possess addictive qualities. Stress is an important factor in the development of addiction and in addiction relapse, and may contribute to an increased risk for obesity and other metabolic diseases. Uncontrollable stress changes eating patterns and the salience and consumption of hyperpalatable foods; over time, this could lead to changes in allostatic load and trigger neurobiological adaptations that promote increasingly compulsive behavior. This association may be mediated by alterations in the hypothalamic-pituitary-adrenal (HPA) axis, glucose metabolism, insulin sensitivity, and other appetite-related hormones and hypothalamic neuropeptides. At a neurocircuitry level, chronic stress may affect the mesolimbic dopaminergic system and other brain regions involved in stress/motivation circuits. Together, these may synergistically potentiate reward sensitivity, food preference, and the wanting and seeking of hyperpalatable foods, as well as induce metabolic changes that promote weight and body fat mass. Individual differences in susceptibility to obesity and types of stressors may further moderate this process. Understanding the associations and interactions between stress, neurobiological adaptations, and obesity is important in the development of effective prevention and treatment strategies for obesity and related metabolic diseases.

Finite element analysis on longitudinal and radial functionally graded femoral prosthesis.

This study focused on developing a 3D finite element model of functionally graded femoral prostheses to decrease stress shielding and to improve total hip replacement performance. The mechanical properties of the modeled functionally graded femoral prostheses were adjusted in the sagittal and transverse planes by changing the volume fraction gradient exponent. Prostheses with material changes in the sagittal and transverse planes were considered longitudinal and radial prostheses, respectively. The effects of cemented and noncemented implantation methods were also considered in this study. Strain energy and von Mises stresses were determined at the femoral proximal metaphysis and interfaces of the implanted femur components, respectively. Results demonstrated that the strain energy increased proportionally with increasing volume fraction gradient exponent, whereas the interface stresses decreased on the prostheses surfaces. A limited increase was also observed at the surfaces of the bone and cement. The periprosthetic femur with a noncemented prosthesis exhibited higher strain energy than with a cemented prosthesis. Radial prostheses implantation displayed more strain energy than longitudinal prostheses implantation in the femoral proximal part. Functionally graded materials also increased strain energy and exhibited promising potentials as substitutes of conventional materials to decrease stress shielding and to enhance total hip replacement lifespan.

Design of new generation femoral prostheses using functionally graded materials: a finite element analysis.

This study aimed to develop a three-dimensional finite element model of a functionally graded femoral prosthesis. The model consisted of a femoral prosthesis created from functionally graded materials (FGMs), cement, and femur. The hip prosthesis was composed of FGMs made of titanium alloy, chrome-cobalt, and hydroxyapatite at volume fraction gradient exponents of 0, 1, and 5, respectively. The stress was measured on the femoral prosthesis, cement, and femur. Stress on the neck of the femoral prosthesis was not sensitive to the properties of the constituent material. However, stress on the stem and cement decreased proportionally as the volume fraction gradient exponent of the FGM increased. Meanwhile, stress became uniform on the cement mantle layer. In addition, stress on the femur in the proximal part increased and a high surface area of the femoral part was involved in absorbing the stress. As such, the stress-shielding area decreased. The results obtained in this study are significant in the design and longevity of new prosthetic devices because FGMs offer the potential to achieve stress distribution that more closely resembles that of the natural bone in the femur.

The ventilation of multiple-bed hospital wards in the tropics: A review.

Hospital and healthcare facilities have diverse indoor environment due to the different comfort and health needs of its occupants. Currently, most ventilation studies revolve around specialised areas such as operating rooms and isolation rooms. This paper focuses on the ventilation of multiple-bed hospital wards in the tropical climate, taking into account the design, indoor conditions and engineering controls. General ward layouts are described briefly. The required indoor conditions such as temperature, humidity, air movements and indoor air quality in the ward spaces are summarized based on the current guidelines and practices. Also, recent studies and engineering practices in the hospital indoor environment are elaborated. Usage of computational fluid dynamics tools for the ventilation studies is discussed as well. As identified during the review, there is an apparent knowledge gap for ventilation studies in the tropics compared with temperate climates, as fact studies have only been published for hospital wards in countries with a temperate climate. Therefore, it is highlighted that specific tropical studies along with novel engineering controls are required in addressing the ventilation requirements for the tropics.

Thermal comfort study of hospital workers in Malaysia.

UNLABELLED: This article presents findings of the thermal comfort study in hospitals. A field survey was conducted to investigate the temperature range for thermal comfort in hospitals in the tropics. Thermal acceptability assessment was conducted to examine whether the hospitals in the tropics met the ASHRAE Standard-55 80% acceptability criteria. A total of 114 occupants in four hospitals were involved in the study. The results of the field study revealed that only 44% of the examined locations met the comfort criteria specified in ASHRAE Standard 55. The survey also examined the predicted percentage of dissatisfied in the hospitals. The results showed that 49% of the occupants were satisfied with the thermal environments in the hospitals. The field survey analysis revealed that the neutral temperature for Malaysian hospitals was 26.4 degrees C. The comfort temperature range that satisfied 90% of the occupants in the space was in the range of 25.3-28.2 degrees C. The results from the field study suggested that a higher comfort temperature was required for Malaysians in hospital environments compared with the temperature criteria specified in ASHRAE Standard (2003). In addition, the significant deviation between actual mean vote and predicted mean vote (PMV) strongly implied that PMV could not be applied without errors in hospitals in the tropics. PRACTICAL IMPLICATIONS: The new findings on thermal comfort temperature range in hospitals in the tropics could be used as an important guide for building services engineers and researchers who are intending to minimize energy usage in heating, ventilating and air conditioning systems in hospitals operating in the tropics with acceptable thermal comfort level and to improve the performance and well-being of its workers.

The use of hyperventilation therapy after traumatic brain injury in Europe: an analysis of the BrainIT database.

OBJECTIVE: To assess the use of hyperventilation and the adherence to Brain Trauma Foundation-Guidelines (BTF-G) after traumatic brain injury (TBI). SETTING: Twenty-two European centers are participating in the BrainIT initiative. DESIGN: Retrospective analysis of monitoring data. PATIENTS AND PARTICIPANTS: One hundred and fifty-one patients with a known time of trauma and at least one recorded arterial blood-gas (ABG) analysis. MEASUREMENTS AND RESULTS: A total number of 7,703 ABGs, representing 2,269 ventilation episodes (VE) were included in the analysis. Related minute-by-minute ICP data were taken from a 30 min time window around each ABG collection. Data are given as mean with standard deviation. (1) Patients without elevated intracranial pressure (ICP) (< 20 mmHg) manifested a statistically significant higher P(a)CO(2) (36 +/- 5.7 mmHg) in comparison to patients with elevated ICP (> or = 20 mmHg; P(a)CO(2): 34 +/- 5.4 mmHg, P < 0.001). (2) Intensified forced hyperventilation (P(a)CO(2) < or = 25 mmHg) in the absence of elevated ICP was found in only 49 VE (2%). (3) Early prophylactic hyperventilation (< 24 h after TBI; P(a)CO(2) < or = 35 mmHg, ICP < 20 mmHg) was used in 1,224 VE (54%). (4) During forced hyperventilation (P(a)CO(2) < or = 30 mmHg), simultaneous monitoring of brain tissue pO(2) or S(jv)O(2) was used in only 204 VE (9%). CONCLUSION: While overall adherence to current BTF-G seems to be the rule, its recommendations on early prophylactic hyperventilation as well as the use of additional cerebral oxygenation monitoring during forced hyperventilation are not followed in this sample of European TBI centers. DESCRIPTOR: Neurotrauma.

The brain monitoring with Information Technology (BrainIT) collaborative network: data validation results.

BACKGROUND: The BrainIT group works collaboratively on developing standards for collection and analyses of data from brain injured patients towards providing a more efficient infrastructure for assessing new health technology. MATERIALS AND METHODS: Over a 2 year period, core dataset data (grouped by nine categories) were collected from 200 head-injured patients by local nursing staff. Data were uploaded by the BrainIT web and random samples of received data were selected automatically by computer for validation by data validation (DV) research nurse staff against gold standard sources held in the local centre. Validated data was compared with original data sent and percentage error rates calculated by data category. FINDINGS: Comparisons, 19,461, were made in proportion to the size of the data received with the largest number checked in laboratory data (5,667) and the least in the surgery data (567). Error rates were generally less than or equal to 6%, the exception being the surgery data class where an unacceptably high error rate of 34% was found. CONCLUSIONS: The BrainIT core dataset (with the exception of the surgery classification) is feasible and accurate to collect. The surgery classification needs to be revised.

BrainIT collaborative network: analyses from a high time-resolution dataset of head injured patients.

BACKGROUND: The BrainIT project was conceived in 1997 and has grown into an international collaboration with the purpose of gathering high time resolution data from head injured patients utilising standardised methodologies. MATERIALS AND METHODS: From 1998, 22 participating neuroscience centres collected three main types of information: demographic, physiological data and clinical treatment information. A data collection solution was provided for each centre dependent on their existing facilities and data were collected for the duration of monitoring as defined by the routine care in each centre. On completion of ICP monitoring all personal information was removed and then transferred to Glasgow via the internet where it was converted into a standard format and entered into a central database. Outcome was measured using the extended Glasgow Outcome Score using an interview questionnaire. FINDINGS: Data has been obtained from a total of 349 patients (277 male and 72 female) The age of these patients ranged from 1 to 87 years (median 31); 145 had been involved in a traffic accident and 32 were pedestrians; 78 had suffered a fall; 24 were assaulted and the remaining 70 of other causes. A large amount of physiological data was collected (e.g. BP 2,531 days, ICP 2,212 days in total). This dataset has provided the opportunity to perform unique analysis and these include the statistical features of blood pressure, diurnal variations in ICP, optimal sampling rate determination and a comparison of summary measures of secondary insults. CONCLUSIONS: This challenging collaboration has brought together a large number of centres and developed a successful clinical research network focussed on improving the treatment of head injured patients. It has successfully collected a vast quantity of high quality data that provides a rich source for analysis and hypothesis testing.

BrainIT: a trans-national head injury monitoring research network.

BACKGROUND: Studies of therapeutic interventions and management strategies on head injured patients are difficult to undertake. BrainIT provides validated data for analysis available to centers that contribute data to allow post-hoc analysis and hypothesis testing. METHODS: Both physiological and intensive care management data are collected. Patient identification is eliminated prior to transfer of data to a central database in Glasgow. Requests for missing/ ambiguous data are sent back to the local center. Country coordinating centers provide advice, training, and assistance to centers and manage the data validation process. RESULTS: Currently 30 centers participate in the group. Data collection started in January 2004 and 242 patients have been recruited. Data validation tools were developed to ensure data accuracy and all analysis must be undertaken on validated data. CONCLUSION: BrainIT is an open, collaborative network that has been established with primary objectives of i) creating a core data set of information, ii) standardizing the collection methodology, iii) providing data collection tools, iv) creating and populating a data base for future analysis, and v) establishing data validation methodologies. Improved standards for multi-center data collection should permit the more accurate analysis of monitoring and management studies in head injured patients.

The BrainIT Group: concept and current status 2004.

INTRODUCTION: An open collaborative international network has been established which aims to improve inter-centre standards for collection of high-resolution, neurointensive care data on patients with traumatic brain injury. The group is also working towards the creation of an open access, detailed and validated database that will be useful for hypothesis generation. In Part A, we describe the underlying concept of the group and it's aims and in Part B we describe the current status of the groups development. METHODS: Four group meetings funded by the EEC have enabled definition of a "Core Dataset" to be collected from all centres regardless of specific project aim. A form based feasibility study was conducted and a prospective data collection exercise of core data using PC and hand held computer based methods is in progress. FINDINGS: A core-dataset was defined and can be downloaded from the BrainIT web-site (go to "Core dataset" link at: www.brainit.org). A form based feasibility study was conducted showing the overall feasibility for collection of the core data elements was high. Software tools for collection of the core dataset have been developed. Currently, 130 patient's data from 16 European centres have been recruited to the joint database as part of an EEC funded proof of concept study. INTERPRETATION: The BrainIT network provides a more standardised and higher resolution data collection mechanism for research groups, organisations and the device industry to conduct multicentre trials of new health care technology in patients with traumatic brain injury.

Accurate data collection for head injury monitoring studies: a data validation methodology.

BACKGROUND: BrainIT is a multi centre, European project, to collect high quality continuous data from severely head injured patients using a previously defined [6] core data set. This includes minute-by-minute physiological data and simultaneous treatment and management information. It is crucial that the data is correctly collected and validated. METHODS: Minute-by-minute physiological monitoring data is collected from the bedside monitors. Demographic and clinical information, intensive care management and secondary insult management data, are collected using a handheld computer. Data is transferred from the handheld device to a local computer where it is reviewed and anonymised before being sent electronically, with the physiological data, to the central database in Glasgow. Automated computer tools highlight missing or ambiguous data. A request is then sent to the contributing centre where the data is amended and returned to Glasgow. Of the required data elements 20% are randomly selected for validation against original documentation along with the actual number of specific episodic events during a known period. This will determine accuracy and the percentage of missing data for each record. CONCLUSION: Advances in patient care require an improved evidence base. For accurate, consistent and repeatable data collection, robust mechanisms are required which should enhance the reliability of clinical trials, assessment of management protocols and equipment evaluations.

Survey of traumatic brain injury management in European Brain-IT centres year 2001.

BACKGROUND: The aim of this study was to obtain basic knowledge about the current local conditions and neurointensive care of traumatic brain injury (TBI) in the new multi-centre collaborative BrainIT group. MATERIALS AND METHODS: The survey comprised a background part on local policies (Part A), and a case study section (Part B). The information was gathered by questionnaire followed by telephone interviews. Twenty-three BrainIT centres participated in the survey and answers from two respondents were available from 18 of the sites. RESULTS: The average proportion of agreement between duplicate respondents was 0.778 (range 0.415-1.00). All BrainIT centres monitored ICP. The treatment protocols seem to have a pattern concerning escalation of treatment of intracranial hypertension: 1/ evacuation of mass lesions and head elevation; 2/ increased sedation and mannitol; 3/ hyperventilation; 4/ ventricular drainage; 5/ craniectomy and barbituates. CONCLUSIONS: There seemed to be an agreement on neurointensive care policies within the BrainIT group. The suggested order of treatment was generally in accordance with published guidelines although the suggested order and combinations of different treatments varied. Variation of treatment within the range of prescribed standards provides optimal conditions for an interesting future analysis of treatment and monitoring data in reality using the BrainIT database.

Assessment of different data representations and averaging methods on the Spiegelberg compliance device.

The Spiegelberg Compliance Device (Spiegelberg KG, Hamburg, Germany) has been available for the automated measurement and calculation of minute by minute intracranial compliance. Widespread practical use has been somewhat limited by the instability of values: especially at low intracranial pressures. We looked at two aspects of a methodology in an attempt to increase the value of the Spiegelberg device in the clinical setting. Firstly, we discussed the difference in representing measured values as elastance (dp/dv) instead of compliance (dv/dp); and secondly we proposed the use of an averaging algorithm called the Exponentially Weighted Moving Average (ewma), which could be applied as a flexible method to follow trends and rapid changes in the elastance (or compliance). Clinical data from sixteen patients were gathered and statistical analysis was focused on three particular aspects, the coefficient of variation which indicates the variability of data values, the correlation between the elastance (or compliance) time series and the underlying ICP signal and the percentage of outliers greater than 2.5 standard deviations from the mean. Our results showed that expressing elastance (dp/dv) instead of compliance (dv/dp) yielded fewer outliers and had a better correlation to ICP, and the ewma method had a better correlation to ICP than the Spiegelberg method.